|
|
Post by tanamedvixen on Jun 11, 2014 8:40:58 GMT -5
this is Martin a solo team member of SCR... i will be happy to help with tech if you need.... or any other area you need help...
|
|
|
|
Post by flier129 on Jun 11, 2014 12:20:10 GMT -5
I can help with grid or chase cones.
|
|
|
|
Post by yellow CR on Jun 11, 2014 14:03:15 GMT -5
this is Martin a solo team member of SCR... i will be happy to help with tech if you need.... or any other area you need help... Thank you sir, we can use the tech help. |
|
|
|
Post by Ken Bury on Jun 13, 2014 6:57:15 GMT -5
I'm in.
|
|
|
|
Post by belcher on Jun 13, 2014 6:59:55 GMT -5
2:00 Sat. for set up?
|
|
|
|
Post by yellow CR on Jun 13, 2014 14:03:53 GMT -5
|
|
|
|
Post by belcher on Jun 16, 2014 6:30:51 GMT -5
May have to bow out on this one. I had a slight brain fart at LJVM this past weekend and found the curb. Sh!t!!!! Will update later. Taking car to the shop now for an alignment and sub frame adjustment. Then to find out if the wheels can be saved.
|
|
|
|
Post by grey ghost on Jun 16, 2014 12:50:02 GMT -5
I help with tech or timing just ask.
thanks Rob Falkner
|
|
|
|
Post by PinkBimmer on Jun 16, 2014 13:17:54 GMT -5
I help with tech or timing just ask. thanks Rob Falkner I have you for audit... if you don't mind |
|
|
|
Post by matthugie on Jun 16, 2014 13:37:37 GMT -5
After a LOT more time, effort, and cursing than anticipated my subframe is finally back in the car. I'll be taking it for an alignment tomorrow, and if that is successful then I'll be there. If not, bring some marshmallows because something is getting set on fire.
|
|
|
|
Post by belcher on Jun 16, 2014 13:53:26 GMT -5
Going to a frame shop this afternoon. YIPPEEEE!!!! Something is bent. Just don't know what. Camber can't go neg. enough on left. Right side still at spec.
|
|
|
|
Post by Steve Eckerich on Jun 16, 2014 13:58:32 GMT -5
Don't forget to enter me please Cyndi. Pro XP.
Will help with setup, whatever needed.
|
|
|
|
Post by matthugie on Jun 16, 2014 14:00:25 GMT -5
Going to a frame shop this afternoon. YIPPEEEE!!!! Something is bent. Just don't know what. Camber can't go neg. enough on left. Right side still at spec. I'm not sure what your suspension setup is, but it's more likely a bent control arm or other suspension component than tweaked frame. |
|
|
|
Post by yellow CR on Jun 16, 2014 14:56:08 GMT -5
Sorry to hear Steve. You do know you can pull a cASSino and find a co-drive at the event. He never knows what he is driving until course walks.
|
|
|
|
Post by PinkBimmer on Jun 16, 2014 16:59:42 GMT -5
Don't forget to enter me please Cyndi. Pro XP. Will help with setup, whatever needed. You in.... |
|
|
|
Post by belcher on Jun 17, 2014 7:17:42 GMT -5
Sorry to hear Steve. You do know you can pull a cASSino and find a co-drive at the event. He never knows what he is driving until course walks. I would except now I don't have a car to drive down there. Wife is taking hers to Durham. I haven't given up yet. I have until 6pm Sat. to cancel my hotel room. |
|
|
|
Post by belcher on Jun 17, 2014 7:24:19 GMT -5
Going to a frame shop this afternoon. YIPPEEEE!!!! Something is bent. Just don't know what. Camber can't go neg. enough on left. Right side still at spec. I'm not sure what your suspension setup is, but it's more likely a bent control arm or other suspension component than tweaked frame. It's going there to get measured. Standard coil over set up. When I took it apart nothing jumped out. Everything seemed the same side to side crude measuring wise. I was really hoping for a shifted sub-frame. But my guess would be that if the sub frame shifted camber should have been altered on the right side too. |
|
|
|
Post by matthugie on Jun 17, 2014 13:23:20 GMT -5
After months of messing with the rear subframe, my car finally has a proper alignment so I'm in! Cyndi, you can put me down for registration.
|
|
|
|
Post by dodgecone on Jun 17, 2014 21:04:43 GMT -5
I'm in for Sunday. Happy to help with Novice Chief duties.
|
|
|
|
Post by grey ghost on Jun 18, 2014 10:44:07 GMT -5
I help with tech or timing just ask. thanks Rob Falkner I have you for audit... if you don't mind no I would be happy to do it for you. thanks Rob. |
|
|
|
Post by yellow CR on Jun 18, 2014 17:51:54 GMT -5
What's the word Darcy?
|
|
|
|
Post by integra55 on Jun 18, 2014 18:31:08 GMT -5
hate to have to miss this … but I'll also be missing the next 2 (Z-Max and Metrolina) … conflicts with other events  |
|
|
|
Post by belcher on Jun 19, 2014 6:41:18 GMT -5
I'm out... car has either a bent strut or spindle. Need to swap sides with the struts or put stock back on to see if the problem moves or stays. I know what I'm doing this weekend.
|
|
|
|
Post by steven6282 on Jun 19, 2014 16:27:18 GMT -5
I see as of right now there is only one person listed for waivers still. Do we have enough on for timing that you'd rather me and Alan show up early to do waivers?
|
|
|
|
Post by PinkBimmer on Jun 19, 2014 16:28:56 GMT -5
I see as of right now there is only one person listed for waivers still. Do we have enough on for timing that you'd rather me and Alan show up early to do waivers? Timing, Timing, Timing... did I mention I want you at timing... SCR is providing some waiver peeps we good there |
|
|
|
Post by steven6282 on Jun 19, 2014 16:36:07 GMT -5
I see as of right now there is only one person listed for waivers still. Do we have enough on for timing that you'd rather me and Alan show up early to do waivers? Timing, Timing, Timing... did I mention I want you at timing... SCR is providing some waiver peeps we good there Lol ok!  |
|
